インタープラス 株式会社

INTERPLAS CO.,LTD

Water Assisted

Injection Moulding

All Metal Decetor

Metal Catcher

Heat & Cool System

USCOOL

Injection Molding

SUMITOMO

IMM Tiber Detector

Tie ber Sensor

Resin

Each Companies

Water Assist

It is one of Assited Injection Moldng System, operated unit by a water every customer could use in everywhere.

 

 

【Characteristic】

■ The volume of water, if a pressure is change, water volume undergo only minimal changes.

This character efficient makes it could keep stable equally internal pressure applied to the inner wall by inject high pressure water into resin.

■ The inner wall surface is also smooth and it suits

pipes for fuel and cooling water.

Metal Catcher

All metal removal device "Metal Catcher" is a possible to set directly the mterial convey line and to use widely su as an inspection of the product.

 

 

【Characteristic】

■ Possible to chose from pressure feed line and vacume feed line.

■ Vertical and horizontal, the direction of transport is becoming each direction transport possible.
■ Not only iron, all non-ferrous metals will be removed. (Brass, copper, stainless steel etc

USCOOL

USCOOL is Heat and Cool moding system by operated electric

 

 

【Characteristic】

■ Difference point for conventional Heat and Cool system, cooling is  by water but heating by steam produced electric power

We are possible to supply the Heat and Cool system of over 200 ℃

■ Also, it is nice news to you could not install electric boiler to your factory for demand Heat and Cool system.
■ It is very suitable for the 2D and a small moldings.

Sumitomo automatic injection molding machine

 

【Characteristic】

FCC system:It is possible to fill to

     accordingly each gas discarge by low

     pressure inside mold.

MCM molding:It could expect the

     efficient of mold maintenace term is

     lengthening and solution of short shot

     by gas burning.

Tie ber Sensor

It is a detector to measure the strain of the tie bar that occurs at when mold clamping of the mold of the molding machine, press, die-casting machine.

 

【Characteristic】

■It encourages corruption and molding of conventional better moldings of the tie bar and mold.

■There are 2 types, you could choose from a multiple type and suitable type for tie bar diameter. Both types make easily adopt and disadopt.

Resin

We have dealings and the following of supply resin makers.

 

 

【Resin Makers】

UMGABS (Ltd.)

Asahi Kasei Co., Ltd.

Idemitsu Lion Composite Co., Ltd.

Ube Industries, Ltd.

Kuraray Co., Ltd.

Shin-Etsu Chemical Co., Ltd.

Nippon Steel Sumikin Chemical Co., Ltd.

Sumitomo Chemical Co., Ltd.

Daicel-Evonik Ltd.

Daicel Polymer Co., Ltd.

DIC (Ltd.)

DSM Japan Engnerring Plastics (Ltd.)

Teijin Kasei Co., Ltd. Techno Polymer Co., Ltd.

DuPont Co., Ltd.

Denki Kagaku Kogyo Co., Ltd.

Tosoh Corporation

Toyo Ink Co., Ltd.

Toyo Styrene Co., Ltd.

Toyobo Co., Ltd.

Toray Industries, Inc.

Du Pont-Toray Co., Ltd.

Japan Polyethylene Co., Ltd.

Bayer Co., Ltd.

(Co.) Prime Polymer

Polyplastics Co., Ltd.

Mitsui Chemicals, Inc.

Mitsubishi Engineering Plastics Co., Ltd.

Mitsubishi Chemical Co., Ltd.

Mitsubishi Rayon Co., Ltd.

Lanxess (Ltd.)

Unitika Ltd.

BASF (Ltd.)

SABIC Innovative Plastics Japan (if)

 

Copyrights(C) Interplas 2015 All Right Reserved

INTERPLAS CO., LTD

Head Office 1-5-11, Uchikanda, Chiyoda-ku,

101-0041,Tokyo,Japan